PVC Pressure Coupling Reducing (Cat 8)
PVC Pressure Coupling Reducing is used to join two PVC pressure pipes of different sizes. Primer and solvent recommended for optimal use. Used to extend pipe lines with different size pipe.
See PVC Bush Reducing to join a smaller pipe to a larger fitting.
NOTE: If you cannot find a size combination here, you may be able to make it up using a combination of a reducing coupling and a reducing bush glued into its smaller end.
Our PVC Pressure Couplings Reducing are Watermark Approved Fittings, manufactured to AS/NZS 1477 Standard.
PVC Pressure Cross
PVC pressure 45° elbows are PVC-U fittings with a solvent-weld socket at both ends. They join two lengths of matching PVC pressure pipe and change the direction of the pipeline by 45°.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These elbows are suited to changing direction or creating offsets in residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure 90° elbows are PVC-U fittings with a solvent-weld socket at both ends. They join two lengths of matching PVC pressure pipe and change the direction of the pipeline by 90°.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These elbows are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
Electrical Conduit Adaptor PVC
Electrical Conduit Adaptor PVC is designed to connect a threadless PVC conduit pipe to a threaded fitting or pipe. Also known as a plain to screw fitting, this adaptor provides a practical solution for transitioning between different connection types within conduit installations.
Commonly used in electrical conduit systems, the adaptor allows secure joining where threaded connections are required, helping support reliable installation and compatibility between conduit components.
Electrical Conduit Cap
For above and below ground use
Electrical Junction Box
Electrical Conduit Junction Box PVC is designed to provide a secure connection point within electrical conduit systems. Featuring a socket joint with a removable cap, this junction box allows convenient access for cable installation, inspection, and maintenance when required.
Approved to Australia and New Zealand standards, this junction box supports reliable performance in electrical installations where conduit connections and cable access points are needed.
PVC pressure end caps are PVC-U fittings with a solvent-weld socket used to stop or blank the end of PVC pressure pipe. They are commonly used to close unused pipework, finish the end of an installation or isolate a section of pipe.
The cap fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These caps are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC Pressure Faucet Elbow (Cat 15)
PVC Pressure Faucet Elbows are 90° elbow fittings, with a PVC pressure pipe socket on one end, and a female BSP thread on the other end. Commonly used to connect risers, sprinklers, and threaded fittings to pipe. Primer and solvent are recommended for joining PVC pressure pipe.
Our PVC Pressure Faucet Elbows are Watermark Approved Fittings, and manufactured to AS/NZS 1477 Standard.
Manifold Fittings
Manifold fittings provide easy installation and quick disassemly for maintenance of irrigation valves. The swivel fitting with pre-installed o-ring means no thread tape and no tools required - hand tighten only.
Made with reliability, long life and durability in mind.
Product Specifications - 3 and 4 Port Manifolds
Product Specifications - Manifold Fittings
PVC Mini Ball Valve
Every Valve is Factory Tested
Pressure to 150 PSI (1000) KPA
Non UV Stabilised
PVC pressure faucet sockets are PVC-U fittings with a solvent-weld socket at one end and a female BSP thread at the other. They connect PVC pressure pipe to a matching male BSP threaded fitting, valve, pump, sprinkler component or other compatible equipment.
The socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The female BSP connection may be the same nominal size as the pipe socket or reduced to suit a smaller male BSP thread.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from its measured outside diameter. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure faucet takeoff adapters are PVC-U fittings with a solvent-weld spigot at one end and a female BSP thread at the other. They connect a matching PVC pressure fitting socket to a male BSP threaded valve, pump, filter, sprinkler component or other compatible fitting or equipment.
The spigot inserts into a matching PVC pressure fitting socket and is joined using PVC priming fluid and pressure-rated solvent cement. This joining method is known as a solvent weld joint, or SWJ. The female BSP end accepts a matching male BSP thread.
PVC fitting sizes are nominal, so the stated spigot size is different from its measured outside diameter. Confirm both the matching socket size and BSP thread size before ordering.
These adapters are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC Pressure Faucet Tee
PVC Pressure Tee Faucet is a tee fitting with a female thread. It has two PVC pressure pipe sockets on opposite ends, and a female BSP thread branching off at 90°. Commonly used to connect risers, sprinklers, and threaded fittings to pipe. Primer and solvent are recommended for joining PVC pressure pipe.
See PVC Tee Snap-on Faucet for faucet tees that snap onto the main line, instead of joining to pipe via sockets.
Commonly used in swimming pool and irrigation applications.
Our PVC Pressure Tees are Watermark Approved Fittings, and manufactured to AS/NZS 1477 Standard.
PVC Flexible Micro Tubing
Comes in 4mm and 5mm sizes and is commonly used for connecting micro irrigation stakes, sprinklers and drippers that are located far away from the main poly pipe water supply
PVC Nipple Male BSP Thread
PVC Pressure Elbow Side Outlet Faucet
PVC Pressure Elbow Side Outlet Faucet is a three-way 90° elbow fitting, with two PVC pressure pipe sockets, and a female BSP thread facing away from the elbow. Commonly used in irrigation systems to connect risers, sprinklers, and threaded fittings to pipe. Primer and solvent are recommended for joining PVC pressure pipe.
See PVC Elbow Side Outlet for PVC side outlet elbows that provide a third socket instead of a female thread.
Our PVC Pressure Elbow Side Outlet Faucet are Watermark Approved Fittings, and manufactured to AS/NZS 1477 Standard.
PVC Pressure Elbow Side Outlet
PVC Pressure Elbow Side Outlet is a three-way 90° elbow fitting, with the third socket facing away from the elbow. Commonly used to make corners in DIY projects like soccer goals, greenhouse frames, and garden netting cages. Primer and solvent recommended for optimal use. Suits PVC pressure pipe only.
See PVC Elbow Side Outlet Faucet for PVC side outlet elbows that provide a female thread instead of a third socket.
Our PVC Pressure Elbow Side Outlet are Watermark Approved Fittings, and manufactured to AS/NZS 1477 Standard.
PVC Pressure Slip Fix (Telescopic Coupling)
PVC Slip Fixes are telescopic fittings used to repair large broken sections of pipe and to make connections in tight places. This fitting can be extended, allowing you to connect pipes and parts that cannot be moved. One side of the fitting is a socket for PVC pressure pipe. The other side of the fitting is a spigot (it has the same outside diameter as a PVC pressure pipe) allowing it to be inserted into another fitting. Telescopic fittings are ideal for repairing and changing systems without dismantling other connections. Primer and solvent recommended for optimal use.
Youtube: How To Install a Slip Fix Coupling
NOTE: If you’re using this fitting to join two pipes, you’ll need a PVC Coupling to join the spigot end.
Our PVC Slip Fixes are Watermark Approved Fittings, manufactured to AS/NZS 1477 Standard.
PVC Pressure Tee Snap-On Faucet
PVC Pressure Tee Snap-On Faucet is a tee fitting with a female thread, that snaps onto an existing pipe line without the need to cut the pipe. The fitting is pushed onto the pipe, and has a female BSP thread. Snap-on connections are only recommended in low-pressure systems. The branch section of the tee is blocked and needs to be drilled after installation to allow water through.
See PVC Tee Snap-On for snap-on tees with a PVC pressure pipe socket.
Our PVC Pressure Tee Snap-On are Watermark Approved Fittings, manufactured to AS/NZS 1477 Standard.
PVC Pressure Tee Snap-On Faucet
PVC Pressure Tee Snap-On Faucet is a tee fitting with a female thread, that snaps onto an existing pipe line without the need to cut the pipe. The fitting is pushed onto the pipe, and has a female BSP thread. Snap-on connections are only recommended in low-pressure systems. The branch section of the tee is blocked and needs to be drilled after installation to allow water through.
See PVC Tee Snap-On for snap-on tees with a PVC pressure pipe socket.
Our PVC Pressure Tee Snap-On are Watermark Approved Fittings, manufactured to AS/NZS 1477 Standard.
PVC Pressure Tapping Saddle
PVC Pressure Tee Plain (Cat 19)
PVC Pressure Tees are used to join three PVC pressure pipes of the same size to form a T junction. This fitting allows you to branch a line off at 90° to your main line. Primer and solvent recommended for optimal use.
See PVC Tee Wye for tees that branch at a 45° angle.
See PVC Tee Snap-on for tees that are pushed onto pipe and snap into place (instead of joining to pipe via sockets).
Commonly used in swimming pool and irrigation applications.
Our PVC Pressure Tees are Watermark Approved Fittings, and manufactured to AS/NZS 1477 Standard.
PVC Threaded Plug
Male BSP Thread
Complies with ASTM D 2466 Sch 40
PVC pressure valve sockets are PVC-U fittings with a solvent-weld socket at one end and a male BSP thread at the other. They connect PVC pressure pipe to a matching female BSP threaded valve, pump, filter or other compatible fitting or component.
The socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The male BSP connection may be the same size as the pipe socket or a different size to suit the required female BSP connection.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from its measured outside diameter. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure valve takeoff adapters are PVC-U fittings with a solvent-weld spigot at one end and a male BSP thread at the other. They connect a matching PVC pressure fitting socket to a female BSP threaded valve, pump, filter or other compatible fitting or equipment.
The spigot inserts into a matching PVC pressure fitting socket and is joined using PVC priming fluid and pressure-rated solvent cement. This joining method is known as a solvent weld joint, or SWJ. The male BSP end connects to a matching female BSP thread.
PVC fitting sizes are nominal, so the stated spigot size is different from its measured outside diameter. Confirm both the matching socket size and BSP thread size before ordering.
These adapters are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC Pressure Wye Tee
PVC Pressure Tee Wye is used to join three PVC pressure pipes of the same size to form a junction. This fitting allows you to branch a line off at 45° to your main line. Primer and solvent recommended for optimal use. Commonly used in irrigation systems.
Our PVC Pressure Tee Wye are Watermark Approved Fittings, manufactured to AS/NZS 1477 Standard
PVC GATE VALVES
Suitable for low pressure applications, the sliding gate valve allows water flow to be shut off.
PVC GATE VALVES
Suitable for low pressure applications, the sliding gate valve allows water flow to be shut off.
Manifold Fittings
Manifold fittings provide easy installation and quick disassemly for maintenance of irrigation valves. The swivel fitting with pre-installed o-ring means no thread tape and no tools required - hand tighten only.
Made with reliability, long life and durability in mind.
Product Specifications - 3 and 4 Port Manifolds
Product Specifications - Manifold Fittings
PVC Swing Check Valve
Non-metal check valve used in systems for backflow prevention.
Maximum opening pressure less than 4kPa
Maximum pressure at 23°C:
Full flow (open) – 1034 kPa
Back pressure (closed) – 517 kPa
- Engineered to maximize flow, responsiveness and for positive shut-off
- Compact, space saving design
- Body constructed from PVC
- High grade EPDM seat
- No metal parts
- Excellent for Pool and Spa and general purpose irrigation use
- Suitable for horizontal and vertical up flow installations
- Angled seat and weighted flapper for low-pressure seal
- Slip x Slip socket connections
PVC Bush Reducing Threaded (CAT 24)
PVC threaded reducing bushes are used to reduce the diameter of a pipe or fitting to a FBSP thread. When installed the fitting allows a smaller size BSP thread to join into the irrigation system.
ASTM. Sch 40
The Rain Bird ESP-ME3 Modular 4 Station Base Outdoor Controller is an expandable irrigation controller for residential and light commercial watering systems. It includes 4 base stations and can be expanded up to 22 stations using compatible Rain Bird ESP-ME 3 or 6 station expansion modules.
The ESP-ME3 is suitable for customers who need a controller that can start small and expand later as more irrigation zones are added. It uses a modular station layout, so additional modules can be installed into the available expansion slots without replacing the whole controller.
This controller supports 4 independent programs with 6 start times per program, station run times from 1 minute to 6 hours, seasonal adjustment, delay watering, manual watering, rain sensor bypass by station and Contractor Default™ save/restore programming.
The ESP-ME3 is LNK WiFi Module compatible, allowing smartphone control through the Rain Bird app when the optional Rain Bird LNK / LNK2 WiFi Module is installed. It also supports wired flow sensor monitoring, making it a practical upgrade from simpler fixed-station controllers where flow alerts and larger station capacity are required.
Rain Bird ESP-ME3 Brochure
Rain Bird ESP-ME3 User Manual
Rain Bird ESP-ME3 Specifications
Rain Bird ESP-ME3 Quick Reference
Rain Bird LNK Wi-Fi Module Brochure
Rain Bird LNK Wi-Fi Module User Manual
Rain Bird LNK Wi-Fi Module Specifications
Rain Bird LNK Wi-Fi Module Alexa Smart Home Integration
Video 1
Video 2
Video 3
Video 4
Video 5
Video 6
Video 7
Video 8
Video 9
Rain Bird Pop Up Body 1800 Series
Made from UV resistant plastic and corrosion resistant stainless steel parts, constructed for long product life. With simple top adjustment to decrease spray distance, no tool required to change nozzles and efficient operation at low pressure the Rain Bird 1800 Series may be for you.
All bodies have a 1/2" (15mm) Female threaded inlet.
All listed sizes are the height of the Pop Up riser (not the height of the body).
Compatible with all Rain Bird spray head nozzles such as: Rotary, R-VAN, U-Series, MPR, HE-VAN, R-VAN, and SQ Series nozzles.
Side and bottom inlets on 6" and 12" models give you the option of less digging while still being able to reach over tall landscapes - you will acheive this by unscrewing the plug from the side inlet and screwing it into the bottom inlet.
Rain Harvesting Easy Clean Mozzie Stoppa 90mm is an insect proof tank overflow screen designed for use in rainwater harvesting systems. It features a mosquito proof mesh that helps prevent insects from entering the tank while allowing overflow water to discharge efficiently.
A spring loaded hinge provides easy access for cleaning and maintenance without the need to disassemble the system, making it convenient for ongoing upkeep. The unit can be permanently installed using solvent cement for secure long term installation.
One end of the Mozzie Stoppa connects to a 90mm stormwater socket, while the other end connects to a 90mm stormwater spigot, matching standard 90mm stormwater pipe sizes.
Key Features
-
Insect and mosquito proof overflow screen
-
Easy clean design with spring loaded hinge
-
Suitable for rainwater harvesting systems
-
Permanent solvent weld installation
-
90mm socket and 90mm spigot connections
-
Designed for simple maintenance access
Applications
-
Rainwater tanks
-
Tank overflow protection
-
Rainwater harvesting systems
-
Residential and rural water storage
-
Mosquito prevention in tank systems
High Pressure Layflat
Commonly used for temporary water supply and drainage
Tough with a very high resistance to abrasion, with a heavy synthetic reinforced PVC wall
Resists most chemical agents
