PVC pressure end caps are PVC-U fittings with a solvent-weld socket used to stop or blank the end of PVC pressure pipe. They are commonly used to close unused pipework, finish the end of an installation or isolate a section of pipe.
The cap fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These caps are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure couplings are PVC-U fittings with a solvent-weld socket at both ends. They join two lengths of matching PVC pressure pipe in a straight line.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These couplings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure compression couplings are PVC-U fittings used to join or repair two lengths of matching PVC pressure pipe without using solvent cement. They have a compression connection at both ends and are particularly useful for quick or wet repairs where the pipework needs to be reconnected mechanically.
The coupling is positioned over the pipe ends and the compression nuts are tightened to form the joint. Suitable lubricant should be used on the pipe to assist installation. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter.
These couplings are suited to repairs and straight-line connections in residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, general water transfer and compatible PVC pressure pipework.
PVC pressure faucet sockets are PVC-U fittings with a solvent-weld socket at one end and a female BSP thread at the other. They connect PVC pressure pipe to a matching male BSP threaded fitting, valve, pump, sprinkler component or other compatible equipment.
The socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The female BSP connection may be the same nominal size as the pipe socket or reduced to suit a smaller male BSP thread.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from its measured outside diameter. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure faucet takeoff adapters are PVC-U fittings with a solvent-weld spigot at one end and a female BSP thread at the other. They connect a matching PVC pressure fitting socket to a male BSP threaded valve, pump, filter, sprinkler component or other compatible fitting or equipment.
The spigot inserts into a matching PVC pressure fitting socket and is joined using PVC priming fluid and pressure-rated solvent cement. This joining method is known as a solvent weld joint, or SWJ. The female BSP end accepts a matching male BSP thread.
PVC fitting sizes are nominal, so the stated spigot size is different from its measured outside diameter. Confirm both the matching socket size and BSP thread size before ordering.
These adapters are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure valve sockets are PVC-U fittings with a solvent-weld socket at one end and a male BSP thread at the other. They connect PVC pressure pipe to a matching female BSP threaded valve, pump, filter or other compatible fitting or component.
The socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The male BSP connection may be the same size as the pipe socket or a different size to suit the required female BSP connection.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from its measured outside diameter. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure valve takeoff adapters are PVC-U fittings with a solvent-weld spigot at one end and a male BSP thread at the other. They connect a matching PVC pressure fitting socket to a female BSP threaded valve, pump, filter or other compatible fitting or equipment.
The spigot inserts into a matching PVC pressure fitting socket and is joined using PVC priming fluid and pressure-rated solvent cement. This joining method is known as a solvent weld joint, or SWJ. The male BSP end connects to a matching female BSP thread.
PVC fitting sizes are nominal, so the stated spigot size is different from its measured outside diameter. Confirm both the matching socket size and BSP thread size before ordering.
These adapters are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, irrigation valves, pump and filter connections, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure 45° elbows are PVC-U fittings with a solvent-weld socket at both ends. They join two lengths of matching PVC pressure pipe and change the direction of the pipeline by 45°.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These elbows are suited to changing direction or creating offsets in residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure 90° elbows are PVC-U fittings with a solvent-weld socket at both ends. They join two lengths of matching PVC pressure pipe and change the direction of the pipeline by 90°.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These elbows are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure faucet elbows are PVC-U 90° fittings with a solvent-weld socket at one end and a female BSP thread at the other. They connect PVC pressure pipe to a matching male BSP threaded connection while changing the direction of the connection by 90°.
The socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The female BSP end accepts a matching male BSP thread, such as a threaded riser, nipple, sprinkler component, valve or other compatible fitting.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from its measured outside diameter. The pipe socket and female BSP thread may be the same nominal size or different sizes. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are commonly used in residential, commercial and agricultural irrigation, garden and landscape watering, sprinkler installations, domestic and rural water supply and other compatible PVC pressure pipework.
PVC pressure side outlet plain elbows are PVC-U fittings with three solvent-weld sockets used to join three lengths of matching PVC pressure pipe at a corner. Two sockets form a 90° elbow, while the side outlet provides a third connection at right angles to the other pipe connections.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems and other compatible PVC pressure pipework where a three-way corner connection is required.
PVC pressure side outlet faucet elbows are PVC-U three-way fittings with two solvent-weld sockets and a female BSP threaded side outlet. The two sockets form a 90° elbow for matching PVC pressure pipe, while the female BSP outlet provides a third connection for a matching male BSP threaded fitting or component.
Each solvent-weld socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The female BSP side outlet accepts a matching male BSP thread, such as a sprinkler riser, nipple or other compatible threaded fitting.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from the measured pipe outside diameter. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, sprinkler installations, domestic and rural water supply and other compatible PVC pressure pipework where a threaded connection is required from a three-way corner fitting.
PVC pressure plain tees are PVC-U fittings with a solvent-weld socket on all three openings. They join three lengths of matching PVC pressure pipe and create a 90° branch from the main pipeline.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These tees are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure snap-on plain tees are PVC-U fittings used to add a 90° branch to an existing PVC pressure pipe without cutting the main pipeline. The snap-on section fits over the outside of the existing pipe, while the plain branch provides a solvent-weld socket for connecting matching PVC pressure pipe.
PVC priming fluid and pressure-rated solvent cement are applied to the prepared mating surfaces before the fitting is snapped onto the existing pipe. Once the fitting is securely installed, a hole is drilled through the existing pipe inside the branch opening to allow water into the new outlet. The branch pipe is then solvent-welded into the PVC pressure socket.
PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. Confirm the correct pipe and branch sizes before ordering.
Snap-on tees are intended for low-pressure applications and are commonly used in irrigation, garden and landscape watering and other compatible low-pressure PVC pressure pipework.
PVC pressure snap-on faucet tees are PVC-U fittings used to add a female BSP threaded branch to an existing PVC pressure pipe without cutting the main pipeline. The snap-on section fits over the outside of the existing pipe, while the branch provides a female BSP thread for connecting a matching male BSP threaded fitting or component.
PVC priming fluid and pressure-rated solvent cement are applied to the prepared mating surfaces before the fitting is snapped onto the existing pipe. Once the fitting is securely installed, a hole is drilled through the existing pipe inside the branch opening to allow water into the threaded outlet. The female BSP branch then accepts a matching male BSP connection, such as a sprinkler riser, nipple or other compatible threaded fitting.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from the measured pipe outside diameter. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
Snap-on faucet tees are intended for low-pressure applications and are commonly used in residential, commercial and agricultural irrigation, garden and landscape watering, sprinkler installations and other compatible low-pressure PVC pressure pipework.
PVC pressure wye tees are PVC-U fittings with a solvent-weld socket on all three openings. They join three lengths of matching PVC pressure pipe, with two sockets forming the main pipeline and the third creating a 45° branch.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These wye tees are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework where an angled branch is required.
PVC pressure faucet tees are PVC-U fittings with two solvent-weld sockets forming a straight pipeline and a female BSP threaded branch at 90°. They join two lengths of matching PVC pressure pipe while providing a threaded branch connection for a matching male BSP fitting or component.
Each socket fits over PVC pressure pipe of the selected nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The female BSP branch connects to a matching male BSP connection, such as a threaded riser, nipple, sprinkler component, valve or other compatible fitting.
PVC pressure pipe sizes are nominal, so the stated pipe size is different from the measured pipe outside diameter. The pipe sockets and female BSP branch may be the same nominal size or different sizes. Confirm both the PVC pressure pipe size and BSP thread size before ordering.
These fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, threaded riser connections, pump systems and compatible PVC pressure pipework.
PVC pressure reducing couplings are PVC-U fittings with a different-size solvent-weld socket at each end. They join two different nominal sizes of PVC pressure pipe in a straight line and provide a transition from the larger pipe size to the smaller pipe size.
Each socket fits over PVC pressure pipe of its matching nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These reducing couplings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure bush reducing fittings are PVC-U fittings with a larger solvent-weld spigot and a smaller solvent-weld socket. They are used to reduce a matching PVC pressure fitting socket to accept a smaller size of PVC pressure pipe.
The larger spigot inserts into a matching moulded PVC pressure fitting socket and is joined using PVC priming fluid and pressure-rated solvent cement. The smaller socket fits over PVC pressure pipe of its matching nominal size and is joined using the same solvent-weld method. The spigot is designed for use with a fitting socket and should not be installed into a PVC pressure pipe socket.
PVC pressure pipe sizes are nominal, so the stated sizes are different from the measured outside diameters. Confirm both the fitting socket size and PVC pressure pipe size before ordering.
These bush reducing fittings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure reducing tees are PVC-U fittings with three solvent-weld sockets. They join two lengths of matching PVC pressure pipe in a straight line and create a smaller 90° branch from the main pipeline.
Each socket fits over PVC pressure pipe of its matching nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated sizes are different from the measured pipe outside diameters. This joining method is known as a solvent weld joint, or SWJ.
These tees are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, pump systems, pool and spa equipment, general water transfer and compatible PVC pressure pipework.
PVC pressure crosses are PVC-U fittings with four solvent-weld sockets. They join four lengths of matching PVC pressure pipe to create a four-way junction, with the connections arranged at 90° to one another.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. This joining method is known as a solvent weld joint, or SWJ.
These crosses are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, sprinkler installations, pump systems, general water transfer and compatible PVC pressure pipework where a four-way connection is required.
PVC pressure barrel union couplings are PVC-U fittings with a solvent-weld socket at both ends and a removable centre union connection. They join two lengths of matching PVC pressure pipe in a straight line while allowing the pipeline to be disconnected and reconnected without cutting the pipe.
Each socket fits over PVC pressure pipe of the same nominal size and is joined using PVC priming fluid and pressure-rated solvent cement. The centre union can then be assembled or disassembled when access to the pipeline, equipment or connected components is required.
PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter. Confirm the correct nominal pipe size before ordering.
These barrel union couplings are suited to residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems, filters, pool and spa equipment, general water transfer and compatible PVC pressure pipework where a removable connection is useful.
PVC pressure slipfix fittings are telescopic PVC-U repair fittings with a solvent-weld socket at one end and a pipe-size solvent-weld spigot at the other. They are used to repair damaged PVC pressure pipe and make connections where existing pipework or components cannot easily be moved.
The telescopic body can be extended to bridge the required gap. The socket fits over PVC pressure pipe of the matching nominal size, while the spigot has the same outside diameter as matching PVC pressure pipe and inserts into a compatible moulded PVC pressure fitting socket. When joining directly between two pipe ends, a separate matching PVC pressure coupling is required on the spigot side.
Both solvent-weld connections are joined using PVC priming fluid and pressure-rated solvent cement. PVC pressure pipe sizes are nominal, so the stated size is different from the measured pipe outside diameter.
Slipfix fittings are suited to repairs and modifications in residential, commercial and agricultural irrigation, garden and landscape watering, domestic and rural water supply, pump systems and compatible PVC pressure pipework.
Video 1
Saddle clips for pressure pipe are used to hold pressure pipe securely against a suitable supporting surface. The clip fits over the pipe and can be fixed in place through the mounting holes on either side.
Select the saddle clip to match the nominal size of the pressure pipe being installed.
These clips are suitable for irrigation, water supply, pump systems and other pressure-pipe installations where the pipe requires secure support.
IMPORTANT: Ezyfit fittings are not suitable for use in pressure applications. They should only be used in non-pressure applications.
IMPORTANT: Ezyfit fittings are not suitable for use in pressure applications. They should only be used in non-pressure applications, such as building frames and other DIY projects.
IMPORTANT: Ezyfit fittings are not suitable for use in pressure applications. They should only be used in non-pressure applications, such as building frames and other DIY projects.
PVC Pressure Tapping Saddle
PVC Pressure Fixed Face Flanges
Drilling complies with ANSI B16.5, Class 150 is compatible with ANSI B16.1 Class 125 compatible with Table D and Table E.
Rubber Gaskets sold seperately.
PVC Pressure Vanstone Flange
PVC Pressure Van Stone Flanges are made of two pieces: a flange with a PVC pressure pipe socket, and a table D & E / ANSI rotating ring. The rotating ring makes bolt alignment easy by moving freely around the flange even when it’s glued to pipe. The bolt holes are pre-drilled. These flanges are chemical and corrosion resistant. Primer and solvent recommended for optimal use. Rubber Gaskets sold separately.
Suited for pressure applications up to 1800kpa (up to 50° Celsius). Table D & E / ANSI drilling.
Commonly used in irrigation systems, pools, plumbing, and industrial applications.
Our PVC Slip Fixes are Watermark Approved Fittings, manufactured to AS/NZS 1477 Standard.
Rubber Gasket
3.2mm thick
PVC Threaded Plug
Male BSP Thread
Complies with ASTM D 2466 Sch 40
PVC Bush Reducing Threaded (CAT 24)
PVC threaded reducing bushes are used to reduce the diameter of a pipe or fitting to a FBSP thread. When installed the fitting allows a smaller size BSP thread to join into the irrigation system.
ASTM. Sch 40
PVC Nipple Male BSP Thread