Grundfos UNILIFT AP12 single-phase pump with tethered float switch
Grundfos UNILIFT AP12 single-phase pump with tethered float switch
UNILIFT AP12.40.08.1 (PUGR96001872); UNILIFT AP12.40.08.A1 (PUGR96023930) 50Hz manufacturer performance curve: head, efficiency and input power against flow.
UNILIFT AP12.40.08.1 (PUGR96001872); UNILIFT AP12.40.08.A1 (PUGR96023930) 50Hz manufacturer performance curve: head, efficiency and input power against flow.
Grundfos UNILIFT AP12 single-phase pump with tethered float switch
UNILIFT AP12.40.08.1 (PUGR96001872); UNILIFT AP12.40.08.A1 (PUGR96023930) 50Hz manufacturer performance curve: head, efficiency and input power against flow.

GRUNDFOS UNILIFT AP12.40.08.A1 DRAINAGE PUMP 0.8KW SINGLE PHASE, FLOAT SWITCH

Grundfos UNILIFT AP12.40.08.A1 suits rainwater, groundwater and suitable non-aggressive grey-water drainage. Its tethered float switch starts and stops the pump as water levels change, providing automatic drainage from sumps and collecting pits. Performance is 120L/min at approximately 12.1m head.

✓ Performance: 120L/min at approximately 12.1m head
✓ Maximum flow: 349.8L/min
✓ Maximum head: 15m
✓ Outlet: 40mm (1 1/2") Rp / BSP female thread
✓ Maximum particle diameter: 12mm; small amounts of suspended solids
✓ Control: tethered float switch
✓ Motor output P2: 0.8kW; 220-240V single phase, Australian plug
✓ 10m cable; maximum installation depth 7m

Grundfos UNILIFT AP12 Official Range Catalogue
AP Installation & Operating Instructions
AP Three-Phase Control Box Instructions

Grundfos UNILIFT AP12 single-phase pump with tethered float switch

Grundfos UNILIFT AP12.40.08.A1 suits rainwater, groundwater and suitable non-aggressive grey-water drainage, with a maximum flow of 349.8L/min and maximum head of 15m. These are separate limits. Actual flow depends on lift and pipe resistance; the matching 50Hz performance curve helps assess expected flow for the installation. Performance is 120L/min at approximately 12.1m head.

The outlet is 40mm (1 1/2") Rp / BSP female thread. Maximum particle diameter is 12mm. The pump suits water containing small amounts of suspended solids, but not sewage, long fibres, stones or aggressive and flammable liquids.

Its tethered float switch starts and stops the pump as water levels change, providing automatic drainage from sumps and collecting pits.

For a permanent float-switch installation, allow a minimum pit diameter of 550mm and depth of 600mm at the minimum free float-cable setting. The float must move freely. Maximum installation depth is 7m with the 10m cable. Keep at least 3m of cable above liquid level. Install on a firm base clear of sludge and mud. Keep the inlet strainer covered during pumping and do not run dry.

This version uses a 220-240V single-phase, 50Hz supply and comes with a 10m cable and Australian plug. Rated motor output P2 is 0.8kW and input power P1 is 1.3kW. Internal thermal overload protection stops an overheated motor and resets automatically after cooling.

Suitable liquid temperature is 0-55°C and pH is 4-10. The pump can operate upright or horizontally with its outlet at the highest point. For permanent installations, Grundfos recommends a union, non-return valve and isolating valve in the outlet pipe. Lift the pump by its handle.

The stainless-steel housing and semi-open stainless-steel impeller provide a compact drainage pump for portable or permanent use. A cooling jacket directs pumped liquid around the motor, supporting partly submerged operation while the inlet strainer remains covered. The removable inlet strainer gives access for cleaning.

Two-year manufacturer warranty, subject to Grundfos warranty terms and applicable consumer rights.

Grundfos UNILIFT AP12 Official Range Catalogue
AP Installation & Operating Instructions
AP Three-Phase Control Box Instructions

✓ Warranty
Two years, subject to Grundfos warranty terms and applicable consumer rights.

✓ Performance
AP12.40.08.A1: 120L/min at approximately 12.1m head; maximum head 15m.

Maximum head is at zero flow. Use the performance chart to check flow at your required head.

✓ Outlet Connection
40mm (1 1/2") Rp / BSP female thread.

✓ Liquid & Solids
Maximum particle diameter: 12mm. Suitable for water containing small amounts of suspended solids.
Rainwater, groundwater and suitable non-aggressive grey water.
Liquid temperature: 0-55°C. Liquid pH: 4-10.
Not for sewage, long fibres, stones or aggressive/flammable liquids.

✓ Operation & Control
Automatic tethered float switch.

✓ Water Levels
AP12.40, 100mm free float cable: start / stop 360mm / 230mm.
AP12.40, 250mm free float cable: start / stop 370mm / 100mm.
Levels measured from pump base.
Minimum stop level during continuous operation or external control: 100mm.
Keep the inlet strainer covered.

✓ Installation
Maximum installation depth: 7m with 10m cable.
Keep at least 3m of cable above liquid level.
Float-switch pit: minimum diameter 550mm and depth 600mm at the minimum free float-cable setting.
Upright or horizontal operation with the outlet highest.
Stand clear of sludge and mud. Lift by the handle.
Permanent outlet pipe: union, non-return valve and isolating valve recommended.

✓ Construction
Pump housing and impeller: AISI 304 stainless steel.
Impeller: semi-open, 12mm particle passage.
Cooling jacket around the motor.
Removable inlet strainer.

✓ Motor & Electrical Supply
Supply: 220-240V single phase, 50Hz.
Input power P1: 1.3kW.
Rated motor output P2: 0.8kW.
Rated current: 5.9A.
Australian plug. Internal thermal overload protection with automatic reset.
Cable length: 10m.
Enclosure: IP68. Insulation: Class F.

✓ Dimensions & Weight
Pump height A: 346mm.
Pump width B: 216mm.
Net weight: 13.4kg.

Recently viewed