Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Black 400g
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Black 400g

ANCHOR BLACK GAL 400G

Anchor Black Gal 400g is a fast-drying enamel primer/topcoat that protects prepared steel against rust and corrosion. Its high-build coating provides a smooth, low-gloss black finish and can be used alone or beneath most single-pack enamel topcoats. Galvanised iron and aluminium require an etch primer first.

✓ Can size: 400g
✓ Coating: Enamel primer/topcoat
✓ Finish: Low-gloss black
✓ Approximate coverage: 1-1.5m² per can

Anchor Cold Gal Specifications
Anchor Cold Gal Safety Data Sheet
Anchor Silver Gal Specifications
Anchor Silver Gal Safety Data Sheet
Anchor Black Gal Specifications
Anchor Black Gal Safety Data Sheet

More Information
Product Specifications
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Black 400g
ANCHOR BLACK GAL 400G
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Cold Galv 400g
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Cold Galv 400g TSAGCG
$15 /each
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Silver 400g
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Silver 400g TSAGS
$15 /each
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Black 400g
Tools Anchor Galvanising Industrial Zinc Protection Aerosol Paint Black 400g TSAGB
$15 /each

Anchor Industrial Black Gal is a high-build enamel coating with adhesion and corrosion-resistant properties for steel. It provides a smooth black finish and can serve as either a protective topcoat or a primer beneath most single-pack enamels.

Apply directly to properly prepared ferrous surfaces such as mild and heavy gauge steel. Aluminium and galvanised iron need a suitable etch primer before Black Gal is applied.

Remove rust to sound metal and clean away grease, oil, dust, wax and salt contamination. Sand previously painted surfaces smooth, and ensure the surface is dry before spraying. Lightly sand and remove dust before applying a compatible topcoat.

Use several light coats rather than one heavy coat. The coating is suitable for splash exposure and is not recommended for continuous submergence. Follow the product-specific drying and curing instructions before handling or topcoating.

Anchor Cold Gal Specifications
Anchor Cold Gal Safety Data Sheet
Anchor Silver Gal Specifications
Anchor Silver Gal Safety Data Sheet
Anchor Black Gal Specifications
Anchor Black Gal Safety Data Sheet

✓ Product & Coating
Anchor Industrial Black Gal aerosol.
Product code: BGAL400.
Net contents: 400g.
Coating type: Oxidising fast-dry enamel primer/topcoat.
Colour: Black.
Gloss: Less than 5 when measured at 60 degrees.

✓ Applications & Protection
Direct application to prepared ferrous metal surfaces, including mild and heavy gauge steel.
May be used as a primer under most single-pack enamels or as a topcoat.
Aluminium and galvanised iron require a suitable etch primer first.
Suitable for splash exposure; not recommended for submergence.
Coating heat resistance: Stable up to 120°C.

✓ Surface Preparation
Remove rust back to sound metal and remove dust, grease, oil, wax and other contamination. Allow the surface to dry before coating.
Wash salt-contaminated surfaces with fresh water and allow to dry.
Sand previously painted surfaces smooth.
Before topcoating, lightly sand, feather edges and remove dust.

✓ Application
Shake vigorously for one minute after the mixing ball is heard.
Spray from approximately 25cm in an even sweeping motion.
Initial application: Two light coats, allowing one minute between coats.
Use additional light coats as required for coverage.
Recommended application temperature: 15-35°C.

✓ Drying, Recoating & Curing
At 25°C and relative humidity below 50%:
Touch dry: Approximately 30 minutes.
Recoat: After two hours.
Full cure: Two to three days.
Allow longer drying in cold conditions.

✓ Coverage
Approximate coverage: 1-1.5m² per 400g can.
Coverage varies with film thickness, conditions and spray technique.

✓ Storage
Recommended storage: 15-30°C, away from sunlight and ignition sources.
Minimum shelf life: Two years when stored as specified.

✓ Safety
Extremely flammable aerosol; keep away from heat, sparks and flames.
Use with adequate ventilation and follow the matching safety data sheet for protective equipment.
Protect from sunlight and do not expose above 50°C.
Dangerous goods: UN 1950, Class 2.1.

✓ Documents
Technical data sheet: CWB ANC014.
Australian aerosol SDS: CAM010701, version 2.0, 10 October 2022.

You may also like

Recently viewed