Grundfos CMB5-46 Basic BASICLINE Booster (100 LPM Max Flow, 0.9kW)
Grundfos CMB5-46 Basic BASICLINE Booster (100 LPM Max Flow, 0.9kW)

GRUNDFOS CM BOOSTER PUMPS WITH PM1

Grundfos CM booster pumps supply clean water for household taps, rainwater use, garden watering and light commercial applications. The PM1 controller starts and stops the pump automatically as water is used. Dry-running protection helps protect the pump if the water supply fails.

✓ CMB 1-36: approximately 36m maximum head; 150kPa start pressure; 1" female inlet
Rated duty: 28.3LPM at 23.7m head
✓ CMB 3-37: approximately 37m maximum head; 150kPa start pressure; 1" female inlet
Rated duty: 51.7LPM at 27.7m head
✓ CMB 5-46: approximately 48m maximum head; 220kPa start pressure; 1 1/4" female inlet
Rated duty: 78.3LPM at 38.6m head
✓ All system outlets: 1" BSP male thread
✓ Single-phase 50Hz supply with Australian plug
✓ Not self-priming; fill the pump and inlet pipe before use

Rated duty pairs show flow at the stated head; they are not maximum-flow ratings.

Grundfos CM Pump Installation & Operating Instructions

Grundfos PM1 Installation & Operating Instructions

Grundfos CMB5-46 Basic BASICLINE Booster (100 LPM Max Flow, 0.9kW)

Grundfos CM boosters provide automatic household and light commercial water supply from clean-water tanks and other suitable water sources. Their fixed-speed multistage design provides pressure for taps, showers and garden irrigation.

CMB 1-36: rated duty 28.3LPM at 23.7m head.
CMB 3-37: rated duty 51.7LPM at 27.7m head.
CMB 5-46: rated duty 78.3LPM at 38.6m head.

The CMB 1-36 and CMB 3-37 have a 1" BSP female inlet.
The CMB 5-46 has a 1 1/4" BSP female inlet.
All three have a 1" BSP male controller outlet.

The controller starts the pump when water use causes pressure to fall below its fixed starting threshold, and stops it when water use ends. The starting threshold cannot be adjusted on the controller. Pressure while the pump runs depends on water flow, inlet pressure and losses through the controller and pipework.

The CMB 1-36 and CMB 3-37 use PM1 controllers with a fixed 150kPa starting threshold.
The CMB 5-46 uses PM1 with a fixed 220kPa starting threshold.

Dry-running protection stops the pump if the controller detects a lack of water. Anti-cycling protection detects repeated starts caused by small leaks and stops the pump with an alarm. Correct the cause and restore the water supply before resetting the controller, as described in the manual.

Rated duty pairs show flow at the stated head; they are not maximum-flow ratings.

Flow decreases as head increases. Choose the pump for the required flow and pressure at the point of use.

Use clean, thin, non-aggressive and non-explosive water without solid particles or fibres, at temperatures from 0°C to 40°C.

These pumps are not self-priming. Fill the pump casing and inlet pipe with clean water before starting, following the installation instructions. Install on a firm, level base in a ventilated position protected from direct sun, rain and frost.

The pump has a cast iron housing, 304 stainless steel impellers and an AVBE shaft seal with EPDM rubber components. The controller includes a non-return valve. The single-phase motor has built-in overload protection.

Two-year Grundfos Australian consumer warranty from purchase, subject to its terms.

Grundfos CM Pump Installation & Operating Instructions

Grundfos PM1 Installation & Operating Instructions

✓ Application
Grundfos CM boosters provide automatic household and light commercial water supply from clean-water tanks and other suitable water sources.

✓ Warranty
Two-year Grundfos Australian consumer warranty from purchase, subject to its terms.

✓ Model Specifications
CMB 1-36
Rated duty: 28.3LPM at 23.7m head (manufacturer reference at 2900rpm).
Maximum total head: approximately 36m.
Inlet: 1" BSP female thread.
System outlet: 1" BSP male thread.
Fixed start pressure: 150kPa.
Motor output P2: 0.5kW.
Controller: PM1-15.

CMB 3-37
Rated duty: 51.7LPM at 27.7m head (manufacturer reference at 2900rpm).
Maximum total head: approximately 37m.
Inlet: 1" BSP female thread.
System outlet: 1" BSP male thread.
Fixed start pressure: 150kPa.
Motor output P2: 0.5kW.
Controller: PM1-15.

CMB 5-46
Rated duty: 78.3LPM at 38.6m head (manufacturer reference at 2900rpm).
Maximum total head: approximately 48m.
Inlet: 1 1/4" BSP female thread.
System outlet: 1" BSP male thread.
Fixed start pressure: 220kPa.
Motor output P2: 0.9kW.
Controller: PM1-22.

✓ Supplied Equipment & Control
The controller starts the pump when water use causes pressure to fall below its fixed starting threshold, and stops it when water use ends. The starting threshold cannot be adjusted on the controller. Pressure while the pump runs depends on water flow, inlet pressure and losses through the controller and pipework.

✓ Performance
Flow decreases as head increases.
Maximum head is an approximate curve reading, rather than the pressure available at every flow.
Rated duty pairs show flow at the stated head; they are not maximum-flow ratings. Manufacturer reference speed: 2900rpm.

✓ Pressure Limits
Maximum operating pressure: 1000kPa.
Inlet pressure plus pump pressure must remain within this limit.

✓ Water Supply
Use clean, thin, non-aggressive and non-explosive water without solid particles or fibres, at temperatures from 0°C to 40°C.

✓ Protection
Dry-running protection stops the pump if the controller detects a lack of water. Anti-cycling protection detects repeated starts caused by small leaks and stops the pump with an alarm. Correct the cause and restore the water supply before resetting the controller, as described in the manual.

✓ Installation & Priming
These pumps are not self-priming. Fill the pump casing and inlet pipe with clean water before starting, following the installation instructions. Install on a firm, level base in a ventilated position protected from direct sun, rain and frost.

✓ Construction
The pump has a cast iron housing, 304 stainless steel impellers and an AVBE shaft seal with EPDM rubber components. The controller includes a non-return valve. The single-phase motor has built-in overload protection.

✓ Electrical Supply
Pump motor enclosure: IP55.
PM1 controller enclosure: IP65.
Motor insulation: Class F.
Built-in motor protection: TP211.
Cable: 1.5m with Australian plug.
Maximum ambient temperature: 50°C.

✓ Electrical & Physical Details
CMB 1-36
Power supply: 220-230V single phase, 50Hz.
Maximum current consumption: 3.30-3.15A.
Rated motor speed: 2750-2780rpm.
Net weight: 13.3kg.
Manufacturer product number: 97530097.

CMB 3-37
Power supply: 220-230V single phase, 50Hz.
Maximum current consumption: 3.30-3.15A.
Rated motor speed: 2750-2780rpm.
Net weight: 13.4kg.
Manufacturer product number: 97530133.

CMB 5-46
Power supply: 220-240V single phase, 50Hz.
Maximum current consumption: 5.4-5.0A.
Rated motor speed: 2750-2790rpm.
Overall dimensions: 381.5mm long x 137mm wide x 301mm high.
Net weight: 16.5kg.
Manufacturer product number: 97530169.

Recently viewed